Top Loading Lifting tower - Capacity 496 lbs Max Height 17 ft - Made in Spain by Fantek
Top Loading Lifting tower - Capacity 496 lbs Max Height 17 ft - Made in Spain by Fantek
Overview
Introducing the ProX XTF-T105D Fantek Top Loading Lifting Tower. When a truss full of lighting has to go up 17 ft and stay there all night, the tower underneath it is not the place to cut corners. This heavy duty lifter raises a maximum load of 496 lbs to a maximum height of 17 ft, using a four section steel mast, a manual winch, and steel locking pins that hold each section at the height you set. It is built for rental houses, production companies, mobile stage crews, and venues that need a dependable ground support lift they can set up fast and trust with expensive gear overhead. Made in Spain by Fantek, the ProX T105D is made for intense, repeated use on real job sites.
Top Loading Design The ProX T105D is a top loading tower, so the load sits directly on top of the mast and lifts straight up. That makes it a strong choice for raising truss spans and lighting rigs where you want the weight centered over the tower. Use two towers together to lift a full truss run evenly from both ends.
Four Section Steel Mast The mast is built from four extensible steel profiles that telescope upward as you crank. Steel construction gives the tower the stiffness it needs to carry close to 500 lbs at full extension, and the four section layout lets it reach 17 ft while still folding down to 5.80 ft for transport.
Steel Cable and Pulley Lift System The sections are raised by a high strength steel cable running on ribbed driven pulleys with SELOIL bearings. This gives you a smooth, controlled lift under load, which matters when you are cranking several hundred pounds of truss and fixtures above a stage or dance floor.
Automatic Steel Locking Pins Automatic locking steel pins fix each mast section at the height you want. Once the tower is at working height, the pins hold the section in place so the load is not relying on the winch alone.
Manual Winch Operation The entire system is operated by a manual winch rated at 1,984.16 lbs. One operator can raise and lower the tower by hand, with no power needed at the lift point, which keeps setup simple at outdoor events and venues with limited power.
Leveling Legs with Non-Slip Rubber Feet The legs open to a 5.09 ft diameter base for a wide, stable footprint. Each leg has a non-slip rubber foot and a leveler, so the tower can be set plumb on uneven ground such as grass, gravel, or sloped pavement.
Specifications The ProX T105D reaches a maximum height of 16.99 ft and has a folded height of 5.80 ft. It handles a maximum load of 496.04 lbs with a minimum load of 55.12 lbs. The base measures 5.09 ft in diameter when unfolded. The mast is built in 4 sections, and the winch is rated at 1,984.16 lbs. Folded for transport, the tower measures 69" H x 18" W x 18" L and weighs 189 lbs.
Recommended Accessory Pair the ProX T105D with the ProX XTF-ATCMOB Fantek Universal Truss Bracket Adjustable T-Adapter to mount truss on top of the tower.
Made in Spain by Fantek Made in Spain by Fantek. Distributed in North America by ProX Live Performance Gear.
Designed by Professionals. Built for Performers. Backed by 40 Years of Excellence.
ProX products are designed by a team of seasoned industry professionals who know firsthand what it means when power fails mid-show. Since 1984, ProX has built its reputation on one principle: every product must perform as hard as the professionals who depend on it. We listen to our customers, and their real-world feedback directly shapes the products we bring to market. The ProX T105D is a direct result of that collaboration. When you choose ProX, you are investing in four decades of hands-on expertise and a brand that has never stopped raising the standard for live performance gear.
- 496 lbs Maximum Load for lifting truss and lighting rigs
- 17 ft Maximum Height with a 5.80 ft folded height for transport
- Top Loading Design lifts vertical loads centered over the mast
- Four Section Steel Mast made from extensible steel profiles
- High Strength Steel Cable with ribbed driven pulleys and SELOIL bearings
- Automatic Steel Locking Pins fix each section at the desired height
- Manual Winch rated at 1,984.16 lbs, no power required
- 5.09 ft Diameter Base for a wide, stable footprint
- Leveling Legs for setup on uneven terrain
- Non-Slip Rubber Feet keep the tower planted
- 55.12 lbs Minimum Load
- Made in Spain by Fantek
- ProX Limited Warranty
All registered trademarks and trade names are properties of their respective owners and are used only for the clarification of the compatibility of our products with the products of the different manufacturers.
Product details
Introducing the ProX XTF-T105D Fantek Top Loading Lifting Tower. When a truss full of lighting has to go up 17 ft and stay there all night, the tower underneath it is not the place to cut corners. This heavy duty lifter raises a maximum load of 496 lbs to a maximum height of 17 ft, using a four section steel mast, a manual winch, and steel locking pins that hold each section at the height you set. It is built for rental houses, production companies, mobile stage crews, and venues that need a dependable ground support lift they can set up fast and trust with expensive gear overhead. Made in Spain by Fantek, the ProX T105D is made for intense, repeated use on real job sites.
Top Loading Design The ProX T105D is a top loading tower, so the load sits directly on top of the mast and lifts straight up. That makes it a strong choice for raising truss spans and lighting rigs where you want the weight centered over the tower. Use two towers together to lift a full truss run evenly from both ends.
Four Section Steel Mast The mast is built from four extensible steel profiles that telescope upward as you crank. Steel construction gives the tower the stiffness it needs to carry close to 500 lbs at full extension, and the four section layout lets it reach 17 ft while still folding down to 5.80 ft for transport.
Steel Cable and Pulley Lift System The sections are raised by a high strength steel cable running on ribbed driven pulleys with SELOIL bearings. This gives you a smooth, controlled lift under load, which matters when you are cranking several hundred pounds of truss and fixtures above a stage or dance floor.
Automatic Steel Locking Pins Automatic locking steel pins fix each mast section at the height you want. Once the tower is at working height, the pins hold the section in place so the load is not relying on the winch alone.
Manual Winch Operation The entire system is operated by a manual winch rated at 1,984.16 lbs. One operator can raise and lower the tower by hand, with no power needed at the lift point, which keeps setup simple at outdoor events and venues with limited power.
Leveling Legs with Non-Slip Rubber Feet The legs open to a 5.09 ft diameter base for a wide, stable footprint. Each leg has a non-slip rubber foot and a leveler, so the tower can be set plumb on uneven ground such as grass, gravel, or sloped pavement.
Specifications The ProX T105D reaches a maximum height of 16.99 ft and has a folded height of 5.80 ft. It handles a maximum load of 496.04 lbs with a minimum load of 55.12 lbs. The base measures 5.09 ft in diameter when unfolded. The mast is built in 4 sections, and the winch is rated at 1,984.16 lbs. Folded for transport, the tower measures 69" H x 18" W x 18" L and weighs 189 lbs.
Recommended Accessory Pair the ProX T105D with the ProX XTF-ATCMOB Fantek Universal Truss Bracket Adjustable T-Adapter to mount truss on top of the tower.
Made in Spain by Fantek Made in Spain by Fantek. Distributed in North America by ProX Live Performance Gear.
Designed by Professionals. Built for Performers. Backed by 40 Years of Excellence.
ProX products are designed by a team of seasoned industry professionals who know firsthand what it means when power fails mid-show. Since 1984, ProX has built its reputation on one principle: every product must perform as hard as the professionals who depend on it. We listen to our customers, and their real-world feedback directly shapes the products we bring to market. The ProX T105D is a direct result of that collaboration. When you choose ProX, you are investing in four decades of hands-on expertise and a brand that has never stopped raising the standard for live performance gear.
Key features
- 496 lbs Maximum Load for lifting truss and lighting rigs
- 17 ft Maximum Height with a 5.80 ft folded height for transport
- Top Loading Design lifts vertical loads centered over the mast
- Four Section Steel Mast made from extensible steel profiles
- High Strength Steel Cable with ribbed driven pulleys and SELOIL bearings
- Automatic Steel Locking Pins fix each section at the desired height
- Manual Winch rated at 1,984.16 lbs, no power required
- 5.09 ft Diameter Base for a wide, stable footprint
- Leveling Legs for setup on uneven terrain
- Non-Slip Rubber Feet keep the tower planted
- 55.12 lbs Minimum Load
- Made in Spain by Fantek
- ProX Limited Warranty
All registered trademarks and trade names are properties of their respective owners and are used only for the clarification of the compatibility of our products with the products of the different manufacturers.