Dual 32U Slam Rack Case with 64U Total Rack Space with Cable Management Rail

Overview

ProX is proud to introduce the ProX XS-SLAM2X32U20LANCER Lancer Dual 32U Slam Rack Case. Big shows run on big racks, and once a system outgrows a single case the gear gets split across two, three or four smaller racks. Every extra case adds weight to the load, space on the truck, and a fresh round of interconnects to patch at every venue, and every one of those connections is a chance for something to go wrong before doors. The ProX XS-SLAM2X32U20LANCER solves that by putting two full 32U rack sections inside one case, so the heart of your system can be built once, wired once, and rolled from show to show as a single unit. Less time patching, fewer cases to track, and more confidence that what worked last night will work again tonight.

Dual 32U Rack Capacity The ProX XS-SLAM2X32U20LANCER gives you 64U of total rack space, split into two 32U sections side by side. That is enough room to house a complete amp rack in one section and processing, networking, power distribution and playback in the other, or to run both sides as one large amplifier bank for a bigger PA. With this much space in a single case, you can stop deciding what gets left out of the rack and start building the system the way it should be built.

Interior Layout and Dimensions The interior measures 45" L x 27.5" W (depth), with each 32U section built to the standard 19" rack width. Rack depth is 20", measured from the outer front rack rail to the outer rear rack rail. Because both sections share the same width and depth, planning is simple. Measure your deepest unit, check it against the 20" figure, and you can map the full layout on paper before a single screw goes in, which saves hours of trial and error on the shop floor.

3.5" Front and Rear Clearance There is 3.5" of open space between the rack and the case at both the front and the back. At the front, that space leaves room for rack handles, knobs, front panel connectors and patch cables, so nothing has to be pulled or bent flat to close up the case. At the rear, power cords, speaker cables and network lines get room to bend naturally and exit cleanly. Cables that are not forced into tight turns last longer, and connectors that are not under constant strain are far less likely to fail mid show.

Built-In Cable Management Center Rail A central rail is built into the case and designed as a dedicated tie point for your cables. Instead of letting runs hang loose or zip tying them to whatever is nearby, you can bundle power, signal and network lines and tie them to the rail so they follow the same path every time. A clean, tied off rack is faster to troubleshoot when the clock is running, easier for a new tech to read at a glance, and much less likely to have a cable shake loose on the road. It also makes the rack look as professional as the show it runs.

Two Racks, One Connected System With both 32U sections in the same case, the connections between them stay made between gigs. Your amps can remain patched to your processing, your network can stay tied into your controllers, and your power distribution can stay wired to everything it feeds. At the venue, that means running a short list of outside connections instead of rebuilding the whole system from scratch. For crews working tight load in windows and back to back dates, that time savings adds up fast.

Built for Large Scale Production The ProX XS-SLAM2X32U20LANCER is a strong fit for touring amp racks, front of house and monitor world processing, broadcast and streaming control systems, and rental companies that need a dependable home for a complete system. It also works well for installed systems that get pulled out for special events, since the entire rack can leave the building as one piece and come back ready to plug in. When the whole show depends on one rack, it makes sense to build that rack into a case designed to handle it.

Designed by Professionals. Built for Performers. Backed by 40 Years of Excellence.

ProX products are designed by a team of seasoned industry professionals who know firsthand what it means when power fails mid-show. Since 1984, ProX has built its reputation on one principle: every product must perform as hard as the professionals who depend on it. We listen to our customers, and their real-world feedback directly shapes the products we bring to market. The ProX XS-SLAM2X32U20LANCER is a direct result of that collaboration. When you choose ProX, you are investing in four decades of hands-on expertise and a brand that has never stopped raising the standard for live performance gear.

• Dual 32U Rack Sections 64U of total rack space in one case
• Standard 19" Rack Width Each section accepts standard 19" rack mount gear
• 20" Rack Depth Measured outer rack rail to outer rack rail
• Interior Dimensions 45" L x 27.5" W (depth)
• 3.5" Front and Rear Clearance Room for handles, connectors and cable bends
• Center Cable Management Rail Built-in tie point for organized cable routing
• One Case System Build Fewer cases to load and fewer interconnects to rebuild
• ProX Limited Lifetime Warranty

All registered trademarks and trade names are properties of their respective owners and are used only for the clarification of the compatibility of our products with the products of the different manufacturers.

Product details

ProX is proud to introduce the ProX XS-SLAM2X32U20LANCER Lancer Dual 32U Slam Rack Case. Big shows run on big racks, and once a system outgrows a single case the gear gets split across two, three or four smaller racks. Every extra case adds weight to the load, space on the truck, and a fresh round of interconnects to patch at every venue, and every one of those connections is a chance for something to go wrong before doors. The ProX XS-SLAM2X32U20LANCER solves that by putting two full 32U rack sections inside one case, so the heart of your system can be built once, wired once, and rolled from show to show as a single unit. Less time patching, fewer cases to track, and more confidence that what worked last night will work again tonight.

Dual 32U Rack Capacity The ProX XS-SLAM2X32U20LANCER gives you 64U of total rack space, split into two 32U sections side by side. That is enough room to house a complete amp rack in one section and processing, networking, power distribution and playback in the other, or to run both sides as one large amplifier bank for a bigger PA. With this much space in a single case, you can stop deciding what gets left out of the rack and start building the system the way it should be built.

Interior Layout and Dimensions The interior measures 45" L x 27.5" W (depth), with each 32U section built to the standard 19" rack width. Rack depth is 20", measured from the outer front rack rail to the outer rear rack rail. Because both sections share the same width and depth, planning is simple. Measure your deepest unit, check it against the 20" figure, and you can map the full layout on paper before a single screw goes in, which saves hours of trial and error on the shop floor.

3.5" Front and Rear Clearance There is 3.5" of open space between the rack and the case at both the front and the back. At the front, that space leaves room for rack handles, knobs, front panel connectors and patch cables, so nothing has to be pulled or bent flat to close up the case. At the rear, power cords, speaker cables and network lines get room to bend naturally and exit cleanly. Cables that are not forced into tight turns last longer, and connectors that are not under constant strain are far less likely to fail mid show.

Built-In Cable Management Center Rail A central rail is built into the case and designed as a dedicated tie point for your cables. Instead of letting runs hang loose or zip tying them to whatever is nearby, you can bundle power, signal and network lines and tie them to the rail so they follow the same path every time. A clean, tied off rack is faster to troubleshoot when the clock is running, easier for a new tech to read at a glance, and much less likely to have a cable shake loose on the road. It also makes the rack look as professional as the show it runs.

Two Racks, One Connected System With both 32U sections in the same case, the connections between them stay made between gigs. Your amps can remain patched to your processing, your network can stay tied into your controllers, and your power distribution can stay wired to everything it feeds. At the venue, that means running a short list of outside connections instead of rebuilding the whole system from scratch. For crews working tight load in windows and back to back dates, that time savings adds up fast.

Built for Large Scale Production The ProX XS-SLAM2X32U20LANCER is a strong fit for touring amp racks, front of house and monitor world processing, broadcast and streaming control systems, and rental companies that need a dependable home for a complete system. It also works well for installed systems that get pulled out for special events, since the entire rack can leave the building as one piece and come back ready to plug in. When the whole show depends on one rack, it makes sense to build that rack into a case designed to handle it.

Designed by Professionals. Built for Performers. Backed by 40 Years of Excellence.

ProX products are designed by a team of seasoned industry professionals who know firsthand what it means when power fails mid-show. Since 1984, ProX has built its reputation on one principle: every product must perform as hard as the professionals who depend on it. We listen to our customers, and their real-world feedback directly shapes the products we bring to market. The ProX XS-SLAM2X32U20LANCER is a direct result of that collaboration. When you choose ProX, you are investing in four decades of hands-on expertise and a brand that has never stopped raising the standard for live performance gear.

Key features

• Dual 32U Rack Sections 64U of total rack space in one case
• Standard 19" Rack Width Each section accepts standard 19" rack mount gear
• 20" Rack Depth Measured outer rack rail to outer rack rail
• Interior Dimensions 45" L x 27.5" W (depth)
• 3.5" Front and Rear Clearance Room for handles, connectors and cable bends
• Center Cable Management Rail Built-in tie point for organized cable routing
• One Case System Build Fewer cases to load and fewer interconnects to rebuild
• ProX Limited Lifetime Warranty

All registered trademarks and trade names are properties of their respective owners and are used only for the clarification of the compatibility of our products with the products of the different manufacturers.